Gradall Forklift Parts

Gradall Forklift Parts - The Gradall excavator was the creation of two brothers Ray and Koop Ferwerda. The excavator was established In the 1940's all through World War II, when there was a shortage of labourers. Partners in a Cleveland, Chandler construction business known as Ferwerda-Werba-Ferwerda, the brothers faced a huge predicament when numerous men left the labor force and signed up in the military, depleting available laborers for the delicate finishing work and grading on highway projects. The Ferwerda brothers opted to build an equipment which will save their company by making the slope grading task less manual, easier and more efficient.

The initial excavator prototype consisted of a device with two industrial beams on a rotating platform fixed to a used truck. There was a telescopic cylinder that was used to move the beams back and forth. This enabled the fixed blade at the far end of the beams to push or pull the dirt. Soon improving the first design, the brothers made a triangular boom so as to add more strength. As well, they added a tilt cylinder which let the boom rotate 45 degrees in either direction. A cylinder was placed at the back of the boom, powering a long push rod to enable the machinery to be equipped with either a bucket or a blade attachment.

The year 1992 marked a significant year for Gradall with their introduction of XL Series hydraulics, the most remarkable change in the company's excavators ever since their creation. These top-of-the-line hydraulics systems allowed Gradall excavators to provide comparable power and high productivity on a realistic level to conventional excavators. The XL Series ended the first Gradall equipment power drawn from low pressure hydraulics and gear pumps. These traditional systems effectively handled grading and finishing work but had a hard time competing for high productivity work.

The new XL Series Gradall excavators proved a significant increase in their digging and lifting ability. These versions were made along with a piston pump, high-pressure hydraulics system that showed great improvements in boom and bucket breakout forces. The XL Series hydraulics system was likewise developed along with a load-sensing capability. Conventional excavators utilize an operator to pick a working-mode; where the Gradall system can automatically adjust the hydraulic power for the job at hand. This makes the operator's general task easier and even saves fuel at the same time.

Once their XL Series hydraulics came onto the market, Gradall was basically thrust into the highly competitive market of equipment meant to tackle pavement removal, excavation, demolition and different industrial tasks. Marketability was further improved with their telescoping boom because of its exclusive ability to work in low overhead areas and to better position attachments.

Click to Download the pdf

Forklift Parts

Aerial Work Platform Attachments

Aerial Work Platform Attachments - Lift trucks are industrial vehicles that facilitate the transportation of heavy stuff, manufactured goods and the storage of commodities. There is a vast range of forklift attachments accessible on the market to be able to permit people to complete specific tasks in a safer and more efficient manner. Farmers for example, normally need to move...

More

---

Gas Forklift Part

Part for Gas Forklift - In the year 1893, inventor Rudolf Diesel developed the diesel engine. The combustion engine functions by providing the heat of compression to burn the fuel and initiate ignition. Then the fuel is injected into the combustion chamber. This design is in contrast to spark ignition engines, like for example petrol or gasoline engines which rely...

More

---

Forklift Alternators and Starters

Forklift Starters and Alternators - Today's starter motor is usually a permanent-magnet composition or a series-parallel wound direct current electrical motor together with a starter solenoid mounted on it. Once current from the starting battery is applied to the solenoid, basically via a key-operated switch, the solenoid engages a lever that pushes out the drive pinion that is located on...

More

---

Electric Forklift Attachment

Electric Forklift Attachment - The greatest benefit to using an electric lift truck over several lift trucks are that these units generate zero emissions. Electric machinery are sometimes required when working inside facilities. Although propane fueled lift trucks can be used inside, the area would need excellent ventilation so as to prevent any health problems. lift trucks which are powered...

More

---

Knuckle Boom Lift Part

Knuckle Boom Lift Parts - Businesses normally need to carry, move, and stock up really heavy cargo. Load sizes from 5 to 10 tons that need to be moved using dependable equipment that can load and support itself. To resolve these concerns, extremely large Boom Trucks were created to carry out these huge tasks. There are a variety of Boom...

More

---

Boom Lift Attachments

Boom Lift Attachment - Boom lifts are machinery that has a platform that can be lowered or lifted to a range of heights, hence making this piece of machinery an important necessity in a wide variety of professions. Accessible in several specialized varieties such as aerial lifts, scissor lift trucks, and knuckle boom lifts, each version functions very specifically. The...

More

---

JLG Forklift Parts

JLG Forklift Parts - After retiring in the late 1960's, John L. Grove embarked on on a cross country RV expedition. After spending numerous years establishing his family built crane company with his brother, John had no idea that this journey would bring about the rise of JLG Industries, Inc. The world leader of mobile aerial work platforms and precision...

More

---

Portable Manlift Attachments

Portable Manlift Attachments - A really good way to make use of industrial machines whenever required for just brief durations is to lease the item from a machine leasing business. These rental businesses assist contracting businesses and a few homeowners perform needed jobs while saving their clients somewhat a bit of money in operating costs. Different industrial machines are accessible...

More

---